Auto ignition coil wholesale manufacturer in China: How does an ignition coil work? The main task of the ignition coil is to transform the on-board voltage of 12V available in the vehicle to the required ignition voltage and then passed on to the spark plug. Basically, the function of the ignition coil is relatively simple to explain. The ignition coil itself contains a primary and a secondary winding. The primary winding has very few turns, while the secondary winding has very many. As soon as the engine control unit sends a signal to the ignition coil, the on-board voltage of 12V flows through the primary winding. Through this process, a magnetic field is built up. As soon as the signal from the engine control unit is interrupted again, this magnetic field is abruptly reduced. This abrupt degradation generates a high voltage in the secondary winding. This high voltage is now transmitted to the spark plug, which consequently generates a spark. See additional info at ignition coil supplier.
A modern ignition coil just looks like a rubber boot that slips onto its spark plug. Up top, there’s an electrical connector for receiving voltage and some threads to mount it securely on the engine. If you were to dissect the component, however, you would find several meters of tightly wound copper wiring that make up the coil pack. These are wrapped around an iron core which receives the 12V current to serve as an electromagnet. The energy stored in the magnetic field of the core is the energy that is transferred to the spark plug. Lastly, the whole coil pack is embedded in a resin insulator to prevent short-circuiting. The ignition coil uses a principle known as Faraday’s law of induction to produce incredible amounts of power, and the same law applies when constructing electric motors as well as generators.
What is the reason? Here are some of them: The power supply voltage is unstable; The resistance of the high-voltage line is abnormal, replace the high-voltage line; There is a short circuit phenomenon in the secondary; The primary current of the ignition controller is too high, causing the ignition coil to overheat; Problems with high temperature and high-pressure wave work well; It is very unlikely that the coil itself is a problem, you can try another brand; The integrated block of the igniter does not work well. Total of 8 R&D personnel in our factory, Haiyan wholesale ignition coil suppliers have more than 15 years of working experience.
The primary winding of an ignition coil will typically contain 150 to 300 turns of wire; the secondary winding will typically contain 15,000 to 30,000 turns of wire, or around 100 times more than the primary winding. The magnetic field is initially created when the vehicle’s electrical system applies approximately 12 volts to the ignition coil’s primary winding. When a spark is required at a spark plug, the ignition system will switch off the current flow to the primary winding, which will cause the magnetic field to collapse. The collapsing magnetic field will induce a voltage into the primary winding in the region of 200 volts; but the voltage induced into the secondary winding will be approximately 100 times greater, around 20,000 volts.
Using a changing magnetic field to induce an electric current: If a coil of wire is exposed to a magnetic field and the magnetic field then changes (or moves), it creates an electric current in the coil of wire. This process is known as ‘inductance’. This can be demonstrated simply by moving a permanent magnet across a coil. The movement or change in the magnetic field or magnetic flux induces an electric current into the coil wire. There are two main factors that affect how much voltage is induced into the coil: The faster the change (or speed of movement) of the magnetic field and the greater the change in the strength of the magnetic field, the greater the induced voltage. The greater the number of windings in the coil, the greater the induced voltage.
The products are produced by Haiyan hardware accessories manufacturer. It is highly resistant to temperature and heat. The manufactured hardware accessories have such merits of as to be used in the area. It is highly resistant to temperature and heat. Haiyan hardware accessories supplier has developed a broad market at home and abroad with its excellent quality, fast delivery, and timely and thoughtful service. It is highly resistant to temperature and heat. Discover more info at https://www.hj-auto.com/.
Haiyan aijian Co.Ltd. is a car ignition coil manufacturer, which are seated on No.338 Yanjia Road, Wanghai Haiyan Jiaxing, Zhejiang, locating western Hangzhou bay cross-sea bridge,3.5 KM far from the Zhajiasu high way exit,1.0 km distance from Huangpu high way exit, convenient transportation, is the centre of economic of shanghai-Ningbo-Hangzhou triangle. The main products of Haiyan wholesale automotive ignition coil manufacturers contain car ignition coil pack, plug coil, spark coil, tool cabinet, hardware accessories, and precision matching pieces of Japanese host, every year manufacturing ignition coils 1,000,000 PCS, cars pare parts 2,000,000 sets,3,000,000 sets of Japanese hosts accessories. Widely export to South and North America, Europe, South Africa, and Asia.