Hydraulic seal manufacturer 2024: A mechanical seal is a very effective device. Every centrifugal pump must accommodate a spinning shaft while mechanically maintaining fluid or gas contained in the “wet end” of the pump. Mechanical seals consists primarily of a rotary seal face with a driving mechanism which rotates at the same speed as the pump shaft, a stationary seal face which mates with the rotary and is retained using a gland or in some pump models an integral stuffing box cover, a tension assembly (utillizing springs or a metal bellows) keeps the rotary face firmly positioned against the stationary face preventing, excluding, and containing contamination and leakage, both when the pump is not in operation and when the pump shaft is rotating. Static sealing gaskets, orings or elastomeric bellows are strategically located to complete the seal assembly. Find extra info on rod seals.
The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart.
It can maintain stable performance after prolonged exposure to various corrosive compounds. Due to its lack of polarity, low unsaturation, and high chemical stability, our gasket has high resistance to various polar chemicals such as alcohols, acids (acetic acid, hydrochloric acid, etc.), strong base (sodium hydroxide, oxidant, hydrogen peroxide), detergents, animal and vegetable oils, ketones and certain esters. It is designed to have excellent aging resistance and excellent resistance to compression set and compression stress relaxation. Therefore, our gasket has significant advantages over other conventional gaskets. Its excellent materials and manufacturing process enables it to achieve effective sealing when exposed to corrosive chemicals, friction, high temperatures or very low temperatures. At the same time, it is easy to install and has industry-leading creep resistance, which saves users a lot of time and cost and increases productivity.
Since the scraper seal is made of the special material, PTFE, it has an impurity immersion function. Therefore, when combined with the piston rod seal and the metal bushing, it can prevent damage to the piston rod and prevent the accumulation of oil pressure. It has a diameter range of 3-1600mm and a temperature range of -30°C + 200°C. The wiper scraper seal can operate at speeds of up to 5 m/s. It has high wear resistance, tear resistance, low-temperature resistance and good strength. Our wiper seals can be used in combination with piston seals and anti-wear rings to prevent oil in the cylinder from being mixed with foreign matter, which causes damage to the working seal. It is especially suitable for piston rods with a large diameter. Moreover, it has a wide range of applications, such as agricultural machinery, injection moulding machines, forklifts, cranes and so on.
Destroy the leak: The working conditions of the sealing part are relatively bad, the thermal deformation is large, it is often subjected to vibration, impact, improper installation, excessive tightening force, repeated use, compression deformation, internal stress concentration, damage beyond the fatigue strength, material aging, deterioration, etc. will cause damage to leaks. This kind of leakage has the greatest impact and great harm, so it is necessary to strengthen prevention.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Read more info on https://www.dmsseals.com/.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.
Construction machinery, also known as construction machinery, is mainly used for mechanical and electrical equipment for the construction, renovation and maintenance of various buildings. Widely distributed in industrial and civil construction, urban construction, national defense construction projects, transportation construction, mining and other raw material industrial construction and production, agriculture, forestry and water conservancy construction, sanitation and environmental protection industries. It contains a wide range of types, such as excavators, loaders, cranes, pump trucks, pile drivers, hydraulic breakers, pavers, graders, rock drills, etc.
It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.