Top wiper seals manufacturer: The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film. Read additional info on https://www.dmsseals.com/.
What are Mechanical Seals? Mechanical seals are devices that accommodate a rotating shaft while containing and preventing the fluid from leaking out of the enclosed housing. While different mechanical seal designs are available for pumping applications, most have three sealing points. Rotating face that rotates with the shaft; Stationary face fitted to the pump housing; Interface portion between the rotating and stationary face of the seal. These three sealing points ensure that the fluid contained within the pump housing does not leak while also preventing dust particles in the atmosphere from entering the housing. The mechanical seals are usually made up of different materials to prevent sticking. Typically, one side of the seal uses softer materials like carbon graphite, and the other is made of harder materials such as silicon carbide or ceramic alumina. However, hard materials are preferred for both surfaces if the pumping application involves abrasive fluids. In addition to the two materials, the sealing unit also comes with O-rings to seal the stationary face on the housing side and the rotating face on the shaft side. Springs are also used to keep both faces pressed. In most cases, the two faces of the seals are also lubricated to prevent friction and wear. Depending on the application, this fluid film can either be a separate lubricant or the process fluid itself.
However, hydraulic transmission also has disadvantages compared with mechanical transmission: It is easy to leak and not friendly to the environment. High manufacturing precision is required. Low efficiency. The transmission ratio is not fixed. Due to the special working environment of construction machinery, its hydraulic system has the following characteristics: The working hours are irregular, and sometimes work continuously for a long time. The working environment is outdoors, the working temperature difference is large, and the working environment is dusty. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small. Due to the volume and weight, the working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa.
The radial force of our rotary seals on the shaft and the distribution is very reasonable. It can achieve the optimal “critical oil film thickness” working condition and always maintain critical lubrication. We guarantee that our rotary seal can help the machine get the sharpest “peak” pressure distribution with the least radial force, providing the best sealing effect. The bearing seal is designed by DMS SEALS to isolate the moving metal part, guiding the piston and piston rod of the hydraulic cylinder to move in a certain direction and it can help withstand lateral loads. It helps prevent any direct contact between the piston metal and the cylinder metal and prevents strain and seal damage on the inner surface of the cylinder.
DMS SEALS’ s bonded seal is ideal for being applied to threaded pipe fittings and plug sealing in Metric, British and BSP systems. The seal has no special requirements for the positioning and processing techniques of the seal groove, so it is an ideal accessory for fast and automatic installation that we highly recommend. The operating temperature range is -30°C ~ 100°C, and the working pressure is less than 39.2 MPa. It is commonly used in a hydraulic oil medium.
Scraper seals are also known as wiper seals. The scraper sealof DMS SEALS can effectively prevent various forms of contamination that cause a hydraulic system failure. It can be mounted on the outside of the piston rod seal of the hydraulic cylinder to protect the hydraulic cylinder from dirt, dust and moisture. It can well protect the hydraulic cylinder from environmental pollution and effectively prevent damage to the hydraulic cylinder parts, causing the system to malfunction. DMS offers a wide range of wiper seals for different hydraulic systems with different characteristics, specifications and combinations.
The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.
The guide belt is a belt-shaped member that guides the moving parts. Its main function is to guide. In order to realize the function of guidance, it must support the guided member, and guide and correct its motion trajectory. In order to realize the guiding function well, it also requires isolation, shock absorption and noise reduction of the guiding parts. Guide belts are mainly used in oil cylinders and cylinders. Due to their excellent performance, they are also widely used in other motion mechanisms. Discover extra info on https://www.dmsseals.com/.
DMS Seals is a professional hydraulic seals, industrial mechanical seals manufacturer and oil seal supplier specializing in supplying sealing solutions and various seals & o ring. As a leading custom o ring manufacturer, DMS can support OEM and ODM and can meet customers’ requests. DMS Seals adheres to the tenet of “first-class design, top manufacturing, excellent service” and strive to be an excellent supplier of sealing system solutions. DMS Seals pays the utmost attention to quality to ensure the satisfaction of our cooperative partners.